FP-3193流速傳感器 美國omega
葉輪流速傳感器
FP-5100 and FP-5300
葉輪流速傳感器
Accurate to ±0.2 fps
Repeatability at ±0.1 fps
Simple and Accurate Flow Measurement
Streamline your flow measurement operation with the FP-5100 Series flow sensor. Using this compact flow sensor, a matched sensor installation fitting, an OMEGA? flow meter or controller, and ordinary handtools, you can assemble a complete flow monitoring or controlling system in minutes. Accurate to ±0.2 fps, with repeatability at ±0.1 fps, this insertion sensor operates on a simple electromechanical principle, proven in thousands of liquid flow applications worldwide. It all adds up to precision, dependability, and convenience– basic advantages that are quickly surpassing its in-line competition.
Convert your maintenance hours into minutes with the FP-5300. Should a sensor, rotor, or O-ring need to be replaced, it takes only seconds. Reduce your system downtime substantially with a stand-alone FP-5300 sensor, or simply add a Wet Tap Assembly and eliminate downtime completely. Combined with the FP-5300 during initial installation, the Wet Tap allows sensor removal without system shut-down. Optional local or remote capability lets you place your meter up to 200 feet away without signal amplification, and you can install the FP-5300 in pipe sizes ranging from 1/2 inch to 36 inches without a lot of additional cost, because the price of the FP-5300 increases only slightly for larger pipe sizes.
Available in a choice of chemically resistant, non-contaminating housing materials, the FP-5300 stands up to the harshest environments. The glass-filled polypropylene housing version is lightweight but strong, which makes it ideal for handling a wide range of liquids, including corrosive fluids in chemical processing. For processes involving acids and solvents, the PVDF (polyvinylidene fluoride) housing version is a tough fluorocarbon that is highly resistant to more severe fluids.
The sensor works on a simple but precise electromechanical principle based on measuring the rate and volume of flow in your pipe. Four permanent magnets, imbedded in the rotor blades, spin past a coil in the sensor body. As the fluid flow causes the rotor to move, a sine wave signal is produced, directly proportional to the flowrate. The patented “open cell” feature of the rotor ensures a linear, repeatable output, up to 20 fps, with accuracy of ±0.2 fps. The result is minimal head loss and no cavitation.
Designed to allow optional conduit installation, the FP-5300 easily lets you comply with local codes requiring conduit protection. For instance, pry off the plug on top of the sensor: underneath, you’ll find a 1/2 FNPT thread. Using an optional conduit adaptor fitting kit, you can connect your conduit FPM-5000-SCAK conduit adaptor kit), and an optional instrument back-cover kit will provide everything you need for quick conduit connection to a meter or controller. Additionally, you can adapt to both rigid and flexible liquid-tight conduits, protecting your system hookup from harsh elements and mechanical damage.
Flow Range
SPECIFICATIONS
Accuracy: ±1% full scale
Output Signal: 1 V p-p/fps
Output Frequency: 6 Hz/fps nominal
Flow Rate Range: 1 to 20 fps
Source Impedance: 8 kΩ
Maximum Pressure:
FP-5300 Series: 180 psig max @ 20°C (68°F)
FP-5100 Series: 200 psig max @ 20°C (68°F)
Minimum Temperature: 0°C (32°F)
Maximum Temperature: See chart on spec sheet for complete temperature and pressure rating
Pressure Drop: Equal to 2.5 m (8') of straight pipe
Material:
Transducer Housing: glass-filled polypropylene or PVDF
O-Rings: FKM
Shaft: Titanium or Hastelloy C(PVDF optional)
Rotor: PVDF
Maximum % Solids: 1% of fluid volume, non-abrasive, nonmagnetic, <100 micron diameter and length
Standard Cable Length: 7.5 m (25')
Max Viscosity: 1 centipoise (water); up to 5 cp above 5 fps velocity
| Pipe Size |
?" | ?" | 1" | 1?" | 1?" | 2" | 2?" | 3" | 4" | 5" | 6" | 8" | 10" | 12" |
| Range (gpm) |
1 to 19 |
1.7 to 34 |
2.7 to 54 |
4.7 to 94 |
6.4 to 127 |
10.6 to 210 |
15 to 300 |
24 to 461 |
40 to 794 |
63 to 1247 |
91 to 1801 |
156 to 3119 |
246 to 4915 |
349 to 6977 |
產品型號/產品描述
Paddlewheel Flow Sensors (Fitting Required)
FP-5300 Titanium shaft polypropylene housing, for pipe sizes 1/2 to 4"
FP-5301 Titanium shaft polypropylene housing, for pipe sizes 5 to 8"
FP-5302 Titanium shaft polypropylene housing, for pipe sizes 10 or larger
FP-5100 Hastelloy C shaft, PVDF housing, for pipe sizes 1/2 to 4"
FP-5101 Hastelloy C shaft, PVDF housing, for pipe sizes 5 to 8"
Wet Tap Units
FP-3193 Titanium shaft polypropylene housing, for pipe sizes 1/2 to 4" Wet Tap Assembly
FP-3194 Titanium shaft polypropylene housing, for pipe sizes 5 to 8" Wet Tap Assembly
FP-3195 Titanium shaft polypropylene housing, for pipe sizes 10" and up Wet Tap Assembly
Popular Fittings
FP-5307 3/4" PVC
FP-5307CU 3/4" Copper
FP-5310M 1" molded PVC
FP-5320GI 2" Galvanized Iron
FP-5340CS 4" Carbon Steel Weldolet
Popular Panel Meters
DPF701 1/8 DIN Panel Meter for Rate or Totalization
DPF75 1/8 DIN Panel Meter for Rate and Totalization
Accessories
FPM-5000-SCAK Sensor Conduit Adapter Kit
FMK-1538-2 Replacement Rotor/Paddlewheel
FMK-1546-1 Replacement titanium rotor pin
FMK-51545-1 Replacement PVDF rotor and rotor pin
注釋: Comes complete with operator's manual.
FP-3193流速傳感器 美國omega
